|本期目录/Table of Contents|

[1]赵江平,史源.基于正交试验的谷物粉尘燃烧特性影响因素研究[J].中国安全生产科学技术,2019,15(2):39-44.[doi:10.11731/j.issn.1673-193x.2019.02.006]
 ZHAO Jiangping,SHI Yuan.Study on factors influencing combustion characteristics of grain dust based on orthogonal tests[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2019,15(2):39-44.[doi:10.11731/j.issn.1673-193x.2019.02.006]
点击复制

基于正交试验的谷物粉尘燃烧特性影响因素研究
分享到:

《中国安全生产科学技术》[ISSN:1673-193X/CN:11-5335/TB]

卷:
15
期数:
2019年2期
页码:
39-44
栏目:
学术论著
出版日期:
2019-02-28

文章信息/Info

Title:
Study on factors influencing combustion characteristics of grain dust based on orthogonal tests
文章编号:
1673-193X(2019)-02-0039-06
作者:
赵江平史源
(西安建筑科技大学 资源工程学院,陕西 西安 710055)
Author(s):
ZHAO Jiangping SHI Yuan
(College of Resources Engineering, Xi’an University of Architecture and Technology, Xi’an Shaanxi 710055, China)
关键词:
玉米淀粉正交试验热释放速率引燃时间
Keywords:
corn starch orthogonal test heat release rate ignition time
分类号:
X932
DOI:
10.11731/j.issn.1673-193x.2019.02.006
文献标志码:
A
摘要:
为了研究谷物粉尘燃烧特性影响因素,以可食用玉米淀粉为研究对象,通过ZY6243锥形量热仪(CONE)进行了单因素和正交试验,研究了粉尘粒径、惰性介质CaCO3质量分数、热辐射通量对玉米淀粉燃烧特性的影响效应。应用直观分析法和方差分析法定性地研究了各因素对玉米淀粉热释放速率峰值的影响程度并进行了排序,2种方法得出的结论基本一致。研究结果表明:各因素对玉米淀粉热释放速率峰值的影响程度依次为:CaCO3质量分数>粉尘粒径>热辐射通量;其中惰性介质CaCO3对热释放速率峰值和引燃时间的影响最为显著。
Abstract:
In order to study the influencing factors of the combustion characteristics of grain dust, taking the edible corn starch as the research object, the single factor and orthogonal tests were carried out by using the ZY6243 cone calorimeter (CONE), and the influence effect of particle size of dust, mass fraction of CaCO3 as inert medium and heat radiation flux on the combustion characteristics of corn starch was studied. The influence degree of each factor on the peak heat release rate of corn starch were studied qualitatively by using the intuitive analysis method and variance analysis method, then they were sorted, and the results obtained by two methods were basically consistent. It showed that the influence degree of each factor on the peak heat release rate of corn starch in descending order was mass fraction of CaCO3, particle size of dust and heat radiation flux, and among which, the influence of CaCO3 as inert medium on the peak heat release rate and ignition time was the most significant.

参考文献/References:

[1]国家技术监督局.《粉尘爆炸泄压指南》:GB/T 15605-1995 [S]. 北京:中国标准出版社,1995.
[2]朱建芳.防火防爆理论与技术[M].北京:煤炭工业出版社, 2013.
[3]李恩科, 石焱. 常见粮食粉尘理化特性的研究[J].工业安全与环保, 2007(9):35-36. LI Enke, SHI Yan. Study on the physicochemical property of commonly-seen grain dust [J]. Industrial Safety Environmental Protection,2007(9): 35-36.
[4]吉喆. 浅谈食品企业粉尘爆炸危害因素和防治措施[J]. 食品科技, 2018, 43(7): 343-345. JI Zhe.On dust explosion hazard factors and in food enterprises Prevention and control measures [J]. Food Science and Technology, 2018, 43(7): 343-345.
[5]ALVARO RAMIREZ, JAVIER GARCIA-TORRENT, PEDRO J. Determination of parameters used to prevent ignition of stored materials and to protect against explosions in food industries[J]. Journal of hazardous materials, 2009(1): 163-167.
[6]张洪铭. 玉米淀粉粉尘火焰传播及热分析动力学特性实验研究[D]. 武汉:武汉理工大学, 2015.
[7]沈德魁, 余春江, 方梦祥,等. 热辐射下常用木材热解的动力学与燃烧特性[J]. 燃烧科学与技术, 2008(5): 446-452. SHEN Dekui, YU Chunjiang, FANG Mengxiang, et al. Kinetic study of thermal decomposition and combustion characteristics of wood under thermal radiation [J]. Journal of Combustion Science and Technology, 2008(5), 446-452.
[8]曹卫国, 郑俊杰, 彭于怀,等. 玉米淀粉粉尘爆炸特性及火焰传播过程的试验研究[J]. 爆破器材, 2016, 45(1): 1-6. CAO Weiguo, ZHENG Junjie, PENG Yuhuai, et al. Experimental study on explosion characteristics and flame propagation process of corn starch dust[J]. Explosive Materials, 2016, 45(1): 1-6.
[9]谢恬, 陈先锋, 张洪铭,等. 玉米淀粉粒径对其粉尘云着火特性的影响[J]. 中国安全科学学报, 2018, 28(4): 53-58. XIE Tian, CHEN Xianfeng, ZHANG Hongming, et al. Effects of particle size on ignition characteristics of corn starch dust cloud [J]. China Safety Science Journal, 2018, 28(4): 53-58.
[10]李陈. 奥克托今粉尘爆炸特性及其热分解研究[D].太原:中北大学,2018.
[11]徐晓楠. 新一代评估方法——锥形量热仪(CONE)法在材料阻燃研究中的应用[J]. 中国安全科学学报, 2003(1): 22-25,84. XU Xiaonan. Application of the new evaluation method in the research of flame-retardant [J]. China Safety Science Journal, 2003(1): 22-25,84.
[12]王康, 李伟,刘运传,等. 热辐射通量对沥青改性PMMA燃烧特性的影响[J]. 化学分析计量, 2016, 25(6): 67-70. WANG Kang, LI wei, LIU Yunchuan,et al. Effect of heat flux to combustion characteristics of asphalt modified PMMA [J]. Chemical Analysis and Meterage, 2016, 25(6): 67-70.
[13]王康, 刘运传, 孟祥艳,等.锥形量热仪测量材料热释放速率的影响因素分析[J]. 消防科学与技术, 2018, 37(4): 449-452. WANG Kang, LIU Yunchuan, MENG Xiangyan, et al. Analysis on the influence factors of heat release rate tested by cone calorimeter[J]. Fire Science and Technology, 2018, 37(4): 449-452.
[14]邹玉叶. 正交实验设计优选教学方法的应用研究[J]. 科教导刊(上旬刊), 2018(6): 108-111. ZOU Yuye. Application research of orthogonal experimental design optimization teaching method [J]. Science Tribune (On the ten-day), 2018(6): 108-111.
[15]刘永岭, 王艳艳. 正交设计优选甘草多糖的提取工艺[J].价值工程, 2018, 37(26): 249-251. LIU Yongling, WANG Yanyan. Study on extraction of glycyrrhiza polysaccharide orthogonal design [J].Value Engineering, 2018, 37(26): 249-251.
[16]王宇斌, 雷大士, 彭祥玉,等. 基于正交试验的某冶炼渣中银的综合回收研究[J]. 矿业研究与开发, 2017, 37(11): 77-80. WANG Yubin, LEI Dashi, Peng Xiangyu, et al. Study on the comprehensive recovery of silver from a smelting slag by orthogonal test[J]. Mining R&D, 2017, 37(11): 77-80.

相似文献/References:

[1]孙晓梅,吕品,刘琛琛,等.基于CFD及正交试验的工作面流场参数优化[J].中国安全生产科学技术,2014,10(4):54.[doi:10.11731/j.issn.1673-193x.2014.04.009]
 SUN Xiao mei,LV Pin,LIU Chen chen,et al.Optimization of flow field parameters in working face based on orthogonal experiment and CFD[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2014,10(2):54.[doi:10.11731/j.issn.1673-193x.2014.04.009]
[2]李 波,刘敦文,余 磊.高速公路路基下采空区充填效果试验研究[J].中国安全生产科学技术,2014,10(5):31.[doi:10.11731/j.issn.1673-193x.2014.05.005]
 LI Bo,LIU Dunwen,YU Lei.Study on filling effect of goaf under highway subgrade[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2014,10(2):31.[doi:10.11731/j.issn.1673-193x.2014.05.005]
[3]王成,洪紫杰,熊祖强.基于瓦斯抽采关键封孔参数及新型封孔材料应用研究[J].中国安全生产科学技术,2016,12(9):65.[doi:10.11731/j.issn.1673-193x.2016.09.012]
 WANG Cheng,HONG Zijie,XIONG Zuqiang.Study on key sealing parameters of gas drainage and application of new sealing material[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2016,12(2):65.[doi:10.11731/j.issn.1673-193x.2016.09.012]
[4]李孜军,郭兆东,吴靓.氯化镁微胶囊泡沫作用机理及阻化效果研究[J].中国安全生产科学技术,2016,12(6):54.[doi:10.11731/j.issn.1673-193x.2016.06.010]
 LI Zijun,GUO Zhaodong,WU Jin.Study on action mechanism and inhibition effect of magnesium chloride microcapsules foam[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2016,12(2):54.[doi:10.11731/j.issn.1673-193x.2016.06.010]
[5]王国荣,伍伟,李明,等.基于正交法X形密封圈力学性能研究[J].中国安全生产科学技术,2017,13(3):144.[doi:10.11731/j.issn.1673-193x.2017.03.023]
 WANG Guorong,WU Wei,LI Ming,et al.Study on mechanical properties of X-shape sealing ring based on orthogonal method[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2017,13(2):144.[doi:10.11731/j.issn.1673-193x.2017.03.023]
[6]李鹏飞,刘启蒙,陈秀艳.影响断层活化的破碎带特征参数敏感性分析[J].中国安全生产科学技术,2017,13(5):16.[doi:10.11731/j.issn.1673-193x.2017.05.003]
 LI Pengfei,LIU Qimeng,CHEN Xiuyan.Sensitivity analysis on characteristic parameters of fracture zone with influence on fault activation[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2017,13(2):16.[doi:10.11731/j.issn.1673-193x.2017.05.003]
[7]史俊伟,孟祥瑞,董羽,等.基于地表沉陷控制的膏体充填材料的性能优化研究[J].中国安全生产科学技术,2017,13(10):143.[doi:10.11731/j.issn.1673-193x.2017.10.024]
 SHI Junwei,MENG Xiangrui,DONG Yu,et al.Study on performance optimization of paste filling material for controlling surface subsidence[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2017,13(2):143.[doi:10.11731/j.issn.1673-193x.2017.10.024]
[8]侯廷凯,周宗红,余洋先,等.岩爆相似材料的最优配比试验研究[J].中国安全生产科学技术,2018,14(11):114.[doi:10.11731/j.issn.1673-193x.2018.11.018]
 HOU Tingkai,ZHOU Zonghong,YU Yangxian,et al.Experimental study on optimum proportion of similar material for rock burst[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2018,14(2):114.[doi:10.11731/j.issn.1673-193x.2018.11.018]
[9]黄鑫,姚韦靖.多因素影响下巷道变形特性数值模拟研究[J].中国安全生产科学技术,2019,15(4):32.[doi:10.11731/j.issn.1673-193x.2019.04.005]
 HUANG Xin,YAO Weijing.Numerical simulation study on deformation characteristics of roadway under multifactor influence[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2019,15(2):32.[doi:10.11731/j.issn.1673-193x.2019.04.005]
[10]吴波,路明,雷领,等.基于正交试验、组合赋权-灰色关联度法研究隧道施工最优方案[J].中国安全生产科学技术,2019,15(8):124.[doi:10.11731/j.issn.1673-193x.2019.08.020]
 WU Bo,LU Ming,LEI ling,et al.Research on optimal scheme of tunnel construction based on orthogonal test and combined weightinggrey correlation method[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2019,15(2):124.[doi:10.11731/j.issn.1673-193x.2019.08.020]

备注/Memo

备注/Memo:
收稿日期: 2018-11-29
作者简介: 赵江平,硕士,副教授,主要研究方向为工业灾害防治理论及技术、工业防毒与职业卫生。
通信作者: 史源,硕士研究生,主要研究方向为粉尘燃烧与爆炸。
更新日期/Last Update: 2019-03-06