|本期目录/Table of Contents|

[1]王永龙,孙玉宁,翟新献,等.棱状钻杆应用于松软突出煤层钻进强度匹配研究[J].中国安全生产科学技术,2014,10(10):48-54.[doi:10.11731/j.issn.1673-193x.2014.10.008]
 WANG Yong-long,SUN Yu-ning,ZHAI Xin-xian,et al.Study on strength matching of prismatic drilling rod when drilling soft and outburst coal seam[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2014,10(10):48-54.[doi:10.11731/j.issn.1673-193x.2014.10.008]
点击复制

棱状钻杆应用于松软突出煤层钻进强度匹配研究
分享到:

《中国安全生产科学技术》[ISSN:1673-193X/CN:11-5335/TB]

卷:
10
期数:
2014年10期
页码:
48-54
栏目:
学术论著
出版日期:
2014-10-31

文章信息/Info

Title:
Study on strength matching of prismatic drilling rod when drilling soft and outburst coal seam
作者:
王永龙孙玉宁翟新献宋维宾王振锋
(河南理工大学 能源科学与工程学院,河南焦作454000)
Author(s):
WANG Yong-long SUN Yu-ning ZHAI Xin-xian SONG Wei-bin WANG Zhen-feng
(School of Energy Science and Engineering, Henan Polytechnic University, Jiaozuo Henan 454000, China)
关键词:
棱状钻杆松软突出煤层钻杆强度安全系数
Keywords:
prismatic drilling rod soft and outburst coal seam drilling rod strength safety factor
分类号:
X936
DOI:
10.11731/j.issn.1673-193x.2014.10.008
文献标志码:
A
摘要:
为解决棱状钻具的强度匹配问题,应用实体设计和数值分析软件,建立不同结构棱状钻具力学分析模型,对其进行强度分析,优化棱状钻具结构。分析结果表明,常规棱状类钻具整体强度匹配不合理,丝扣位置存在受力薄弱点,安全系数较低且整体分布不均衡。可采取加大接头直径、优化接头及棱边结构、应用摩擦焊接工艺等技术手段提高棱状钻具整体强度;改进后的棱状钻杆,整体安全系数分布均衡、波动小,钻杆整体力学性能得到了有效的提高。通过工程应用,解决了煤矿复杂条件煤层钻孔施工丢钻、断钻频繁的被动局面,平均深度超过了设计深度,钻进效率提高20
Abstract:
To solve the problem in strength matching of prismatic drilling rod, the mechanical analysis model of different prismatic drilling rods were established by the physical design and numerical analysis software, and its strength and edges structure were analyzed. The results showed that the strength matching of conventional prismatic drilling rod is unreasonable. The thread of drilling rod exists the problems of vulnerabilities, lower safety factor and unbalance distribution. The technical means, such as increasing the diameter of the joint, optimizing joint and edge structure, and applying friction welding technology etc., were adopted to improve the overall strength of the prismatic drilling rod. The overall safety factor of improved prismatic drilling rod had more balanced distribution and less undulation, and the overall mechanical properties of the drilling rod were effectively improved. By engineering application, the problems of drilling rod dropping and breaking frequently when drilling in complex conditions coal seam were solved. The average depth of borehole exceeded the design depth, and the drilling efficiency improved by 20%, without the accidents of drilling rod dropping and breaking during the test.

参考文献/References:

[1]国务院办公厅.国务院办公厅关于进一步加快煤层气(煤矿瓦斯)抽采利用的意见[G/OL].北京:国务院办公厅,2013
[2]宋晓丹,孔令峰,洪保民,等.我国煤层气产业发展政策现状分析与发展建议[J].天然气工业,2013(2):1-6 SONG Xiao-dan, KONG Ling-feng, HONG Bao-min, et al. The status quo of policies and the propposals for the development of coalbed methane gas industry in China[J]. Natural Gas Industry, 2013(2): 1-6
[3]朱红青,张民波,冯世梁,等.高位孔抽采上被保护层卸压瓦斯的研究及其应用[J].中国安全科学学报,2013, 23(2):92-96 ZHU Hong-qing, ZHANG Min-bo, FENG Shi-liang, et al. Study on relief- pressure gas drainage in upper protected layer with high- level borehole and its application[J]. China Safety Science Journal, 2013, 23(2): 92-96
[4]李维光.低透气性薄煤层煤与瓦斯共采技术研究[J].中国安全生产科学技术,2012, 8(10):14-17 LI Wei-guang. Study on technology of simultaneous coal mining and gas drainage for poor permeability thin seam[J]. Journal of Safety Science and Technology, 2012, 8(10): 14-17
[5]孙玉宁,王永龙,翟新献,等.松软突出煤层钻进困难的原因分析[J].煤炭学报,2012, 37(1):117-121 SUN Yu-ning, WANG Yong-long, ZHAI Xin-xian, et al. Analysis on reasons of drilling difficulty in soft and outburst coal seam[J]. Journal of China Coal Society, 2012, 37(1): 117-121
[6]林柏泉,李庆钊,杨威,等.基于千米钻机的“三软”煤层瓦斯治理技术及应用[J].煤炭学报,2011, 36(12):1968-1973 LIN Bai-quan, LI Qing-zhao, YANG Wei, et al. Gas control technology and applications for the three- soft coal seam based on VLD- 1000 drilling systems[J]. Journal of China Coal Society, 2011, 36(12): 1968-1973
[7]姚 克,孙保山,殷新胜,等.ZDY系列履带定向钻机的研制及应用[J].煤炭科学技术,2013, 41(3):28-31,54 YAO Ke, SUN Bao-shan, YAN Xin-sheng, et al. Development and application of ZDY series crawler mode directional drilling RIG[J]. Coal Science and Technology, 2013, 41(3): 28-31,54
[8]王永龙,孙玉宁,翟新献,等.松软突出煤层新型钻进技术研究[J].采矿与安全工程学报,2012, 29(2):289-294 WANG Yong-long, SUN Yu-ning, ZHAI Xin-xian, et al. Study on new drilling technology in soft and outburst SEAM[J]. Journal of Mining & Safety Engineering, 2012, 29(2): 289-294
[9]林柏泉,邹全乐,沈春明,等.双动力协同钻进高效卸压特性研究及应用[J].煤炭学报,2013(6):911-917 LIN Bai-quan, ZOU Quan-le, SHEN Chun-ming, et al. 外文标题缺失[J]. Journal of China Coal Society, 2013(6): 911-917
[10]郭金钢,孙玉宁,王永龙,等.屯留矿松软突出煤层提高钻进深度研究[J].中国煤炭,2011, 37(4):5-6,91 GUO Jin-gang, SUN Yu-ning, WANG Yong-long, et al. Study on enhancing drilling depth in soft and outburst seam in Tunliu mine[J]. China Coal, 2011, 37(4): 5-6,91
[11]凌标灿,戴世鑫,曹承平,等.三棱钻杆在中软煤层顺层瓦斯抽排钻孔的应用[J].煤炭科学技术,2009, 37(10):44-46,111 LING Biao-can, DAI Shi-xin, CAO Cheng-ping, et al. Application of triangular drilling rod to gas drainage borehole drilling in medium soft SEAM[J]. Coal Science and Technology, 2009, 37(10): 44-46,111
[12]张幼振,石智军,田东庄,等.高强度大通孔钻杆接头圆锥梯形螺纹的有限元分析及改进设计[J].煤炭学报,2010, 35(7):1219-1223 ZHANG You-zhen, DAN Zhi-jun, TIAN Dong-zhuang, et al. Finite element analysis and improved design for taper trapezium joint threads of high- strength drilling rod with big hole[J]. Journal of China Coal Society, 2010, 35(7): 1219-1223
[13]狄勤丰,陈锋,王文昌,等.双台肩钻杆接头三维力学分析[J].石油学报,2012, 33(5):871-877 DI Qin-feng, CHEN Feng, WANG Wen-chang, et al. Three-dimensional mechanical analysis of the double-shouldered tool joint[J]. ACTA Petrolei Sinica (Petroleum Processing Section), 2012, 33(5): 871-877

相似文献/References:

[1]韩晓明,张龙列,刘瑜,等.松软突出煤层水平钻孔反循环气力排屑机理[J].中国安全生产科学技术,2015,11(5):26.[doi:10.11731/j.issn.1673-193x.2015.05.004]
 HAN Xiao-ming,ZHANG Long-lie,LIU Yu,et al.Chip removal mechanism by air reverse circulation during horizontal drilling in soft outburst coal seam[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2015,11(10):26.[doi:10.11731/j.issn.1673-193x.2015.05.004]

备注/Memo

备注/Memo:
国家科技支撑计划项目(2013BAA03B02);河南理工大学博士基金资助项目(B2014-053)
更新日期/Last Update: 2014-12-12