[1]蔡志杰,赵天奉,曹博,等.水下连接器试压帽结构动态仿真及密封性分析[J].中国安全生产科学技术,2019,15(5):85-91.[doi:10.11731/j.issn.1673-193x.2019.05.014]
CAI Zhijie,ZHAO Tianfeng,CAO Bo,et al.Dynamic simulation and sealing performance analysis on structure of pressuretesting cap in underwater connector[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2019,15(5):85-91.[doi:10.11731/j.issn.1673-193x.2019.05.014]
点击复制
水下连接器试压帽结构动态仿真及密封性分析
CAI Zhijie,ZHAO Tianfeng,CAO Bo,et al.Dynamic simulation and sealing performance analysis on structure of pressuretesting cap in underwater connector[J].JOURNAL OF SAFETY SCIENCE AND TECHNOLOGY,2019,15(5):85-91.[doi:10.11731/j.issn.1673-193x.2019.05.014]
《中国安全生产科学技术》[ISSN:1673-193X/CN:11-5335/TB]
- 卷:
- 15
- 期数:
- 2019年5期
- 页码:
- 85-91
- 栏目:
- 职业安全卫生管理与技术
- 出版日期:
- 2019-05-31
文章信息/Info
- Title:
- Dynamic simulation and sealing performance analysis on structure of pressuretesting cap in underwater connector
- 文章编号:
- 1673-193X(2019)-05-0085-07
- Keywords:
- pressuretesting cap; sealing ring; sealing performance; finite element simulation; dynamic simulation; contact stress
- 分类号:
- X937;TE952
- 文献标志码:
- A
- 摘要:
- 为解决水下连接器现有力学模型过于简化，预紧力加载不够合理，密封性能分析结果不够准确的问题，基于ABAQUS有限元模拟提出了新的动态接触分析方法，针对水下连接器试压帽双头螺柱结构，探究了安装和试压工况中该结构形式的密封特性及其与等效拧紧力矩的非线性关联。研究结果表明：在塑性失效设计准则范围内，2种工况下密封环的Mises值最大为399.4 MPa；安装工况下，随预紧力的增加，密封环上、下锥面最大接触应力先增大后略微减小；1 145 Nm螺栓拧紧力矩可完成安装工况，并能在试压工况中保证各部件不被弹开；试压工况下，随试验内压的增加，密封环上锥面最大应力缓慢增加，下锥面最大接触应力几乎不变，最终2值近似相等约为850 MPa，密封宽度合理。
- Abstract:
- In order to solve the problems of simplified mechanical model, unreasonable pretightening force loading and inaccurate analysis results of sealing performance about the underwater connectors, a new analysis method of dynamic contact based on ABAQUS finite element model was proposed. Aiming at the doubleend stud structure of the pressuretesting cap in the underwater connector, the sealing characteristics of the structure form and its nonlinear correlation with the equivalent tightening moment under the installation and pressuretesting conditions were explored. The results showed that within the range of design criteria about the plastic failure, the maximum Mises value of the sealing ring under two conditions was 399.4 MPa. Under the installation condition, the maximum contact stress of the upper and lower conical surfaces of sealing ring increased first and then decreased slightly with the increase of pretightening force. The tightening moment of bolt as 1 145 Nm could complete the installation condition and ensure that all the components were not bounced off in the pressuretesting condition. Under the pressuretesting condition, with the increase of testing internal pressure, the maximum stress on the upper conical surface of sealing ring increased slowly, while the maximum contact stress on the lower conical surface almost remained unchanged, and finally the two values were approximately equal to 850 MPa, with the reasonable sealing width.
参考文献/References:
［1］LARSON E D,KEOSOFF K G.Marginal Subsea Develop-ment with Existing Subsea Trees［C］.//Innovation without limits / OTC .04.2004:1-5.
［2］唐文献,曹伟枫,张建,等.水下井口连接器密封结构性能分析［J］.石油机械, 2016,44(3):82-87.
TANG Wenxian,CAO Weifeng,ZHANG Jian,et al. Perfo-rmance analysis of subsea wellhead connector sealing structure［J］. China Petroleum Machinery,2016,44(3):82-87.
［3］BUITRAGO J, KRISHNAN V R, SOMMERFIELD P M. Fatigue asses-smement of subsea tree connectors and weelheads［C］.//ASME 2011 30th International Conference on Ocean. Offshore and Arctic Engineering, 2011(3):423-432.
［4］李志刚,运飞宏,姜瑛,等.水下连接器密封性能分析及实验研究［J］.哈尔滨工程大学学报,2015,36(3):389-393.
LI Zhigang,YUN Feihong,JIANG Ying,et al. Analysis and experimental study of subsea connector’s seal performance［J］.Journal of Harbin Engineering University,2015,36(3):389-393.
［5］王仁华.深海水平式卡箍连接器密封结构优化分析与性能研究［D］.哈尔滨：哈尔滨工程大学，2017.
［6］梁乃章.关于透镜式密封的螺栓载荷计算［J］.广西大学学报(自然科学版),1988(2):16-19.
LIANG Naizhang.The calculation with the anchor bolts of lens washer seal［J］. Journal of Guangxi University (Natural Science Edition), 1988(2):16-19.
［7］彭飞,段梦兰,王金龙,等.深水大直径连接器双重密封设计［J］.润滑与密封,2014,39(3):105-109,114.
PENG Fei,DUAN Menglan,WANG Jinlong,et al. Design of double seals of deep-water large diameter connector ［J］. Lubrication Engineering ,2014,39(3):105-109,114.
［8］彭飞,段梦兰,范嘉堃,等.深水连接器锁紧机构双重密封设计研究［J］. 机械设计与制造,2014(4):7-10.
PENG Fei,DUAN Menglan,FAN Jiakun,et al. Research on design scheme for double seals of the locking me-chanism for deep-water connector［J］. Machinery Design & Manufacture, 2014(4):7-10.
［9］黄小光,韩忠英.基于ABAQUS的压力容器有限元接触分析［J］.石油化工设备,2011,40(2):35-39.
HUANG Xiaoguang,HAN Zhongying. Contact analysis of pressure vessel based on ABAQUS［J］.Petro-chemical Equipment,2011,40(2):35-39.
［10］陈晓芳,赵宏林,罗晓兰,等.水下卧式采油树井口连接器VX钢圈力学特性研究［J］.石油机械,2014,42(8):62-67.
CHEN Xiaofang,ZHAO Honglin,LUO Xiaolan,et al. Study on mechanical properties of the VX gasket of subsea horizontal christmas tree wellhead connector［J］. China Petroleum Machinery, 2014,42(8):62-67.
［11］唐亚辉.VX金属密封圈热力耦合分析及密封特性研究［D］.北京：中国石油大学(北京),2016.
［12］秦桦,安晨,徐健,等.水下采油树油管悬挂器K形金属密封环密封性能模拟分析［J］.中国海上油气,2017,29(5):141-148.
QIN Hua， AN Chen, XU Jian, et al.Simulation analysis of sealing performance of the K—type metal sealing ring on subsea christmas tree tubing hanger［J］. China Offshore Oil and Gas, 2017,29(5):141-148.
［13］FLITNEY R.Seals and sealing handbook［M］.5th-ed.Oxford: Elsevier Science Ltd,2007: 91-92.
［14］曹金凤，石亦平.ABAQUS有限元分析常见问题解答［M］.北京：机械工业出版社，2009：234-262.
［15］陈晓芳.水下采油树油管悬挂器轴向密封件设计研究［D］.北京：中国石油大学（北京），2015.
相似文献/References:
备注/Memo
- 备注/Memo:
-
收稿日期： 2019-01-18；数字出版日期： 2019-05-23
基金项目： 国家重点研发计划重点专项项目（2016YFC0303700）；国家科技重大专项（2016ZX05028-003-005）
作者简介： 蔡志杰,硕士研究生，主要研究方向为深水油气装备作业安全技术与理论。
通信作者： 赵天奉，博士，副研究员，主要研究方向为海底管道设计校核与失效分析、海洋结构物健康监测与安全评定、海洋钻井平台作业应用技术。
